PCAPTURE Log Messages

Message 1 - Protocol analyzer capture program <name>

Explanation:

This message displays the revision code of the pcapture software.

Action:

None.

Message 2 - Bad ZINIT call, error: <reason>

Explanation:

This message is issued when an attempt to initialize access to ZCOM has failed from pcapture. This will be accompanied by a text reason message from the ZCOM subsystem.

Action:

Address the reason and run pcapture again.

Message 3 - Bad ZOPEN call, error: <reason>

Explanation:

This message is issued when an attempt to get the primary ZLU for pcapture has failed. This will be accompanied by a text reason message from the ZCOM subsystem.

Action:

Address the reason and run pcapture again.

Message 4 - Program already running - terminating this copy

Explanation:

This message is issued when another copy of the pcapture program is already running in the system. This copy of the pcapture program will be terminated.

Action:

None.

Message 5 - Bad ZREAD call, error: <reason>

Explanation:

This message is issued when an attempt to read from the pcapture ZLU has failed. This will be accompanied by a text reason message from the ZCOM subsystem.

Action:

Address the reason and run pcapture again. Note that pcapture will try zread again until the maximum number of reads has been exceeded. Restart pcapture.

Message 6 - Max ZREAD error exceeded - terminating

Explanation:

This message is issued when the number of zread errors has exceeded the maximum number of zread errors allowed. The zread error will have been logged before this error is logged.

Action:

Address the zread error.

Message 7 - End of pcapture

Explanation:

This message is issued when the pcapture program is about to exit.

Action:

If the pcapture program terminates abnormally, try to correct the problems that will be displayed prior to this message. Do nothing if it is a normal termination.

Message 8 - Unexpected message type received <error>

Explanation:

This message is issued when a message with an unknown message type has been read from the pcapture primary ZLU.

Action:

None; however if this problem persists, contact your HP support representative.

Message 9 - Bad ZLTSTORE for label <number> size <number>, Error:<reason>

Explanation:

This message is issued when an attempt to get the logical terminal table storage has failed. This will be accompanied by a text reason message from the ZCOM subsystem.

Action:

Correct the problem with the indicated reason. Review the .answ file to make sure that the analyzer related configuration is correct.

Message 10 - Shutdown received from pdisplay - Terminating pcapture

Explanation:

This message is issued when a shutdown message is received from pdisplay; the pcapture program will be terminated.

Action:

None.

Message 11 - Cannot malloc terminal table buffer, size <size> needed - terminating

Explanation:

This message is issued when pcapture is attempting to allocate memory, and there is not enough free memory on the HP 9000 system.

Action:

Correct the memory shortage problem and retry.

Message 12 - Get pcapture semaphore failed: <error>

Explanation:

This message is issued when pcapture fails to obtain the pcapture semaphore.

Action:

Report this problem to your HP support representative.

Message 13 - pcapture daemon is already active, terminating this copy.

Explanation:

This message is issued when there is another pcapture program already active in the system, this copy of pcapture will be terminated.

Action:

None.

Message 200 - ZLUs are already active

Explanation:

This message is displayed when the analyzer is already running on specified ZLU.

Action:

Correct the problem and retry if it is necessary.

Message 201 - Too many analyzer sessions are already active

Explanation:

This message is displayed when there are already too many active analyzer sessions in the system and there is not enough room to allow an additional one.

Action:

The maximum number of analyzer sessions has been reached, must reduce the current active session before a new session is allowed.

Message 202 - Cannot open <file>, <error>

Explanation:

This message is displayed when pcapture fails to open the indicated file.

Action:

Try to correct the problem with the indicated reason for error.

Message 203 - Cannot write header to <file>, <error>

Explanation:

This message is displayed when pcapture fails to write the header to the indicated file.

Action:

Try to correct the problem with the indicated reason for error. If this problem persists, report it to your HP support representative.

Message 204 - Error enabling analyzer ZLUs

Explanation:

This message is displayed when pcapture fails to enable and activate the analyzer ZLUs. Everything will be shutdown if this problem occurs.

Action:

Try to correct the problem with any indicated reason for error. If this problem persists, report it to your HP support representative.

Message 205 - ZLUs are already stopped

Explanation:

This message is displayed if the ZLUs are already stopped.

Action:

Must enable and activate the ZLUs first before they can be used.

Message 206 - Cannot malloc() buffer for file capture data

Explanation:

This message is displayed if there is not enough free memory in the system to allocate for the file buffer.

Action:

Correct the memory shortage problem and retry.